Showroom

Transparent acrylic deep matte varnish with basecoat

1. TM---M007/--TXX 2. JL---M070/----- 3. JO-03M077/----- 1. Oak veneer sanded with 180 grit paper. Spray application of TM-M007 / Txx series basecoat. Drying for 1 hour. 2. Spray two coats of JL — M070 with an interval of 8 hours and sanded with 320 grit paper. After the second coat, dry for 12 hours and lightly sand with 320 grit paper. 3. Apply JO-03M077. Dry for 24 hours.

Transparent cycle closed pores deep matte

1. FI---M190/----- 2. PL---M151/----- 3. FO-05M237/----- 1. Elm veneer base sanded with 180 grit paper. Spray the FI-M190 insulator to prevent discoloration. Drying for 3-4 hours. 2. Spray several coats (until the pores close), PL-M151 with a gap of 20 to 30 minutes between coats, without sanding between coats. After the last layer, drying for 24 hours and sanding with 320 grit paper. 3. Apply matt varnish FO-05M237. Dry for 12 hours.

PU transparent matt varnish with basecoat

1. TM---M006/--TXX 2. FL---M400/----- 3. FO-20M006/----- 1. Oak veneer base sanded with 180 grit paper. Spray application of TM-M006 / Txx series basecoat. Dry for 1 hour. 2. Spray two coats of FL-M400 with an interval of 16 hours and sand with 320 grit paper. After the second coat, dry for 16 hours and sand with 320 grit paper. 3. Apply matt varnish FO-20M006. Dry for 16 hours.

PU colored varnish with semi-matt acrylic

1. FL---M042/--C02 2. FO-25M060/CS025 3. JO-40M070/----- 1. MDF board base. Apply two coats of FL — M042 / -CO2 by spraying. Spacing between layers of 12 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Application of the final matt varnish FO-25M060 / CS025. Dry for 16 hours and lightly sand with 400 grit paper. 3. Application of acrylic semi-matt varnish JO-40M070. Dry for 24 hours.

Open pore with acrylic white varnish with patina

1. JO-20M800/--BNC 2. GM---M048/--C18 3. JO-25M070/----- 1. Ash veneer base sanded with 180 grit paper. Spray two to three coats of JO-20M800 / –BNC . Spacing between coats of 4-6 hours and sand with 320 grit paper. After the last coat, dry for 12 hours. 2. Spray application of patina GM — M048 / –C18. After drying, sand the patina to achieve the desired effect. 3. Application of acrylic matt varnish JO-25M070. Dry for 24 hours.

Open pore with acrylic white varnish with silver patina

1. JO-20M800/--BNC 2. GM---M048/--C47 3. JO-25M070/----- 1. Ash veneer base sanded with 180 grit paper. Spray two to three coats of JO-20M800 / –BNC. Spacing between coats of 4-6 hours and sand with 320 grit paper. After the last coat, dry for 12 hours. 2. Spray application of patina GM — M048 / –C47. After drying, sand the patina to achieve the desired effect. 3. Application of acrylic matt varnish JO-25M070. Dryfor 24 hours.

Open pore with acrylic white matt varnish

1. JO-20M800/--BNC 1. Ash veneer base sanded with 180 grit paper. Spray two to three coats of JO-20M800 / –BNC. Spacing between layers of 4-6 hours and sand with 320 grit paper. After the last layer, dry for 24 hours.

Open pore with acrylic colored matt varnish

1. JO-20M800/CS175 1. Ash veneer base sanded with 180 grit paper. Spray two to three coats of JO-20M800 / CS175. Spacing between layers of 4-6 hours and sand with 320 grit paper. After the last layer, dry for 24 hours.

Digital printing

1. YL---M641/--C02 2. YO-20M785/----- 1. MDF board base. Spray two coats of YL — M641 / -CO2, with an interval between coats of 8 hours and sand with 320 grit paper. After the last coat, dry for 8 hours and gradually sand with 320, 400, 600 grit papers. 2. Digital printing. 3. Apply YO-20M785. Dry for 48 hours.

“Cameleon” effect

1. PL---M005/--C01 2. JW---M400/I0409 1. MDF board base. Apply two coats of PL-M005 / -C01 by spraying. Spacing between layers of 8 hours and sandi with 320 grit paper. After the last layer, dry for 8 hours and sand with 320 grit paper. 2. Apply JW — M400 / I0409. Dry for 48 hours.

Brushed pore with acrylic matt color varnish

1. JO-20M800/CS004 1. Ash veneer base pre-brushed. Two to three coats JO-20M800 / CS175 were applied by spraying. Interval between layers of 4-6 hours and sanding with 320 grit paper. After the last layer, dry for 24 hours.

“Marble” effect

1. PL---M004/--C02 2. FO-25M060/--BNC 3. TM---M006/--T04 4. JB---M671/----- 1. MDF board base. Apply two coats of PL-M004 / -CO2 by spraying. Spacing between layers of 8 hours and sand with 320 grit paper. After the last layer, dry for 8 hours and sand with 320 grit paper. 2. Apply FO-25M060 / –BNC. Dry 16 hours. 3. Apply TM-M006diluted with acetone 1: 200 in a very small amount. Spray aceton under very low pressure (in drops) to react with the basecoat and give the desired effect. Dry for 30 minutes. 4. Application JB — M671. Dry for 48 hours. Polish if needed.

Open pore with acrylic white varnish semi-matt

1. JO-20M800/--BNC 2. JO-40M070/----- 1. Ash veneer base sanded with 180 grit paper. Spray two to three coats of JO-20M800 / –BNC . Interval between layers of 4-6 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 400 grit paper. 2. Application of acrylic semi-matt varnish JO-40M070. Dry for 24 hours.

Acrylic color cycle

1. JO-20M800/CS128 1. MDF board base. Spray three to four coats of JO-20M800 / CS128. The interval between layers is 4-6 hours and sanding with 320 grit paper. After the last layer, dry for 24 hours.

PU white varnish with acrylic deep matte

1. FL---M042/--C02 2. FO-25M060/--BNC 3. JO-03M077/----- 1. MDF board base. Apply two coats of FL — M042 / -CO2 by spraying. Spacing between layers of 12 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Applyof the final matt varnish FO-25M060 / –BNC. Dry for 16 hours and lightly sand with 400 grit paper. 3. Apply acrylic matt varnish JO-03M077. Dry for 24 hours.

Copper effect

1. JW --- M379 / - NTR 2. EF --- M370 / - C66 3. AF --- C295 / ----- 1. Oak veneer base pre-sanded with 180 grit paper. Spray JW-M379 / -NTR varnish pre-mixed with EF-M370 / -C66 powder in a ratio of 1: 1 and catalyzed by 10% FC-M070 catalyst. 2. To obtain a true metallic effect, fix the surface with AF-C295 after drying. Dry for 24 hours.

Metallo Fuso effect with print

1. PRIMER QUIK 3 2. METALLO FUSO 02 3. ROLLER 4. FO-20M006/----- 1. Apply Primer Quik 3 to the MDF board with a roller. Dry for 1-2 hours. 2. Spray Metallo Fuso 02 Bronzo. 3. Immediately after application with a ribbed roller pass over the surface in two directions to form a mesh. After 16-20 hours of drying, sand gradually from coarser to finer papers 320, 600, 1000, 2000, in order to achieve a metallic effect. 4. Apply topcoat FO-20M006. Dry for 24 hours.

Metallo Fuso effect with print

1. PRIMER QUIK 3 2. MATERIA MT 06 3. ROLLER 4. METALLO FUSO 04 5. FO-20M006/----- 1. Apply Primer Quik 3 to the MDF board with a roller. Dry for 1-2 hours. 2. Apply stainless steel trowel to Materia MT 06. Immediately after application, make an impression with a rubber roller. After 12 hours of drying, lightly sand with 150 grit paper. 3. Spray Metallo Fuso 04 Ottone. After 16-20 hours of drying, sand gradually from coarser to finer papers 320, 600, 1000, 2000, in order to achieve a metallic effect. 4. Apply topcoat FO-20M006. Dry for 24 hours.

Cromo 2 Oro effect

1. FL---M042/--C02 2. PR.916.4 3. REFLEX 4. CROMO 2 ORO 5. AW 382 K/01 1. MDF board base. Apply two coats of FL — M042 / -CO2 by spraying. Spacing between layers of 12 hours and sand with 320 grit paper. After the last layer, dry for 12 hours andsand lightly with 320 grit paper. 2. Apply black PR.916.4. Dry 1-2 hours. 3. Apply Reflex varnish. Dry 18-20 hours. 4. Spray the effect of Cromo 2 Oro. Dry 18-20 hours. 5.Apply topcoat AW 382 K / 01. Drying for 24 hours.

Pietra Di Lavagna, magnet

1. FL---M042/--C02 2. YW---M524/--C96 3. PIETRA DI LAVGNA 1. MDF board base. Apply two coats of FL — M042 / -CO2 by spraying. Spacing between layers of 12 hours and sanding with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Spray apply water magnetized varnish YW — M524 / –C96. Dry6-8 hours. 3. Spray the water-based blackboard Pietra di Lavagna in black. Dry for 48 hours.

Metallo Fuso effect with print

1. PRIMER QUIK 3 2. MATERIA MT 06 3. ROLLER 4. METALLO FUSO 03 5. FO-20M006/----- 1. Apply Primer Quik 3 to the MDF board with a roller . Dry for 1-2 hours. 2. Apply stainless steel trowel to Materia MT.06. Immediately after application, make an impression with a rubber roller. After 12 hours of drying, lightly sand with 150 grit paper. 3. Spray Metallo Fuso 03 Rame. After 16-20 hours of drying, sand gradually from coarser to finer papers 320, 600, 1000, 2000, in order to achieve a metallic effect. 4. Apply topcoat FO-20M006. Dry for 24 hours.

Metallo Fuso Ferro with pattern

1. FL---M042/--C02 2. METALLO FUSO 05 3. ROLLER 4. JO-25M070/----- 1. MDF board base. Apply two or three coats of FL — M042 / -CO2 by spraying. Spacing between layers of 12 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and light sanding with 320 grit paper. 2. Apply the Metallo Fuso 05 Ferro effect. Immedieatly after press with a rubber roller make an impression. After 16-20 hours of drying, sand gradually from coarser to finer papers 320, 600, 1000, 2000, in order to achieve a metallic effect. 3. Apply JO-25M070. Dry for 24 hours.

Wood effect

1. YL---C254/R8019 2. YS---M009/----- 1. MDF board base. Spray the YL — C254 / —- previously tinted to the desired shade. Immediately after applying the foundation, use the tool to make an impression. Dry 4 hours. 2. Fix the surface by applying YS — M009 oil. Dry for 24 hours.

Metallo Fuso Ottone on wood veneers

1. METALLO FUSO 04 2. JO-25M070/----- 1. Ash veneer base sanded with 180 grit paper. Spray Metallo Fuso 04 Ottone. After 16-20 hours of drying, sand gradually from coarser to finer papers 320, 600, 1000, 2000, in order to achieve a metallic effect. 2. Apply finishing varnish JO-25M070. Dryfor 24 hours.

Metallo Fuso Ottone

1. PRIMER QUIK 3 2. MATERIA MT 06 3. METALLO FUSO 04 4. FO-20M006/----- 1. Apply Primer Quik 3 to the MDF board with a roller. Dry for 1-2 hours. 2. Apply Materia MT06. After 12 hours of drying, lightly sand with 150 grit paper. 3. Spray Metallo Fuso 04 Ottone. After 16-20 hours of drying, sand gradually from coarser to finer papers 320, 600, 1000, 2000, in order to achieve a metallic effect. 4. Apply topcoat FO-20M006. Dry for 24 hours.

PU transparent deep matt varnish

1. FL---M400/----- 2. FO-10M006/----- 1. Walnut veneer base sanded with granulation paper 180. Spray two coats of FL-M400 with a gap of 16 hours and sand with 320 grit paper. After the second coat, dry for 16 hours and lightly sand with 400 grit paper. 2. Apply matt varnish FO-10M006. Drying 12 hours.

Transparent PU gloss varnish

1. FL---M400/----- 2. FO-90M006/----- 1. Cherry veneer base sanded with 180 grit paper. Spray two coats of FL-M400 with a gap of 16 hours and sand with 320 grit sandpaper. After the second coat, dry for 16 hours and lightly sand with 400 grit paper. 2. Apply gloss varnish FO-90M006. Dry for 12 hours.

Transparent acrylic matt varnish

1. JL---M070/----- 2. JO-25M070/----- 1. Elm veneer sanded with 180 grit paper. Spray two coats of JL — M070 with an interval of 8 hours and sand with 320 grit sandpaper. After the second layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Apply JO-25M070. Dry for 24 hours.

PU transparent cycle with basecoat and patina

1. TM---M006/--TXX 2. FL---M400/----- 3. GM--M048/--CXX 4. FO-20M006/----- 1. Walnut veneer base sanded with 180 grit paper. Spray application of TM-M006 / Txx stain. Dry for 1 hour. 2. Spray two coats of FL-M400 primer with an interval of 16 hours and sandblasted with 320 grit paper. After the second coat, dry for 16 hours. 3. Spray patina GM — M048. After drying, sand the patina to achieve the desired effect. 4. Apply matt varnish FO-20M006. Dry for 16 hours.

Transparent nitro matt varnish with basecoat

1. TM---M006/--TXX 2. NL---M001/----- 3. NO-10M001/----- 1. Beech veneer base sanded with 180 grit paper. Spray application of TM-M006 / Txx series basecoat. Dry for 1 hour. 2. Spray two coats of NL-M001 with an interval of 4 to 6 hours and sand with 320 grit paper. After the second coat, dry for 8 hours and sand with 320 grit paper. 3. Apply NO-10M001. Dry 16 hours.

Fire-retardant transparent PU matt varnish

1. FL 0510 2. FO2510 3. FC 1110 1. Oak veneer base sanded with 180 grit paper. Spray two coats of FL 0510 base coat catalyzed with 50% catalyst FC1110, 24 hours apart and sanding with 320 grit paper. After the second coat, dry for 24 hours and lightly sand with 320 grit paper. . 2. Apply FO 2510 topcoat catalyzed with 50% FC1110 catalyst. Dry for 24 hours.

High gloss acrylic cycle

1. JL---M071/----- 2. JB---M671/----- 1. Elm veneer base sanded with 180 grit paper. Spray two of three coats of JL — M071 with an interval of 8 hours and sand with 320 grit sandpaper. After the last layer, dry for 12 hours and lightly sand with 400 grit paper. 2. Apply of the final gloss varnish JB — M671. Dry for 48 hours.

PU deep matte colored varnish

1. PL---M004/--C02 2. FO-05M060/CS006 1. MDF board base. Apply two coats of PL-M004 / -CO2 by spraying. Spacing between layers of 8 hours and sand with 320 grit paper. After the last layer, dry for 8 hours and sand with 320 grit paper. 2. Apply matt varnish FO-05M060 / CS006. Dry for 48 hours.

PU white high-gloss varnish

1. PL---M004/--C02 2. FB---M066/--BNC 1. MDF board base. Apply two coats of PL-M004 / -CO2 by spraying. Interval between layers of 8 hours and sand with 320 grit paper. After the last layer, dry for 8 hours and sand with 320 grit paper. 2. Apply the final gloss varnish FB — M066 / –BNC. Dry for 48 hours. Polish if needed.

PU white matt varnish

1. FL---M492/--C02 2. FO-25M060/--BNC 1. MDF board base. Apply two coats of FL-M492 / -CO2 by spraying. Spacing between layers of 12 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Apply the final matt varnish FO-25M060 / –BNC. Dry for 24 hours.

PU White semi-matt varnish

1. FL---M042/--C02 2. FO60M060/--BNC 1. MDF board base. Apply two coats of FL — M042 / -CO2 by spraying. Spacing between layers of 12 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Apply the final semi-matt varnish FO-60M060 / –BNC. Dry for 24 hours.

“Cracquelet” effect

1. YL---C642/--C02 2. YO-05M760/R9005 3. YO-05M760/--SBN 4. AY---M425/----- 5. YO-05M785/----- 1. MDF board base. Spray two coats of YL — C642 / -CO2 with an interval between coats of 8 hours and sand with 320 grit paper. After the last coat, dry for 8 hours and lightly sand with 320 grit paper. 2. Apply final matt varnish YO-05M760 / R9005. Dry for 12 hours and lightly sand with 320 grit paper. 3. Apply final matt varnish YO-05M760 / –SBN. Dry for 2 hours. 4. Spray application of cracquelet varnish AY — M425. 5. After drying, apply the final matt varnish YO-05M785. Dry for 24 hours.

Water-based matt colored varnish – effect “Structur”

1. YL---C642/--C02 2. YO-30M760/CS078 3. AY---M467/----- 1. MDF board base. Spray two coats of YL — C642 / -CO2 with an interval between coats of 8 hours and sand with 320 grit paper. After the last coat, dry for 8 hours and lightly sand with 320 grit paper. 2. Application of the final matt varnish YO-30M760 / -CS078 with the addition of paste structures AY — M467. Dry for 24 hours.

Water-based white deep matte varnish

1. YL---M641/--C02 2. YO-05M785/-SBN 3. YC---M402/----- 1. MDF board base. Spray two coats of primer YL — M641 / -CO2 catalyzed with 4% catalyst YC — M402, with an interval between coats of 8 hours and sand with 320 grit paper. After the last coat, dry for 8 h and lightly sand with 320 grit paper. 2. Application of the final matt varnish YO-05M785 / -SBN catalyzed with 10% catalyst YC — M402. Dry for 24 hours.

Acrylic nature effect

JO--00M294/----- 1. Oak veneer base sanded with granulation paper 180. Spray two coats of JO-00M294 with an interval of 8-12 hours and sand with granulation paper 320. After the second layer dry for 24 hours.

Water-based transparent deep matt

1. YL---M653/----- 2. YO-05M785/-NTR 3. YC---M402/----- 1. Oak veneer base sanded with 180 grit paper. Spray two coats of YL — M653 primer coated with 4% YC — M402 catalyst, with an interval between coats of 4 to 6 hours and sanding with 320 grit paper. After the second coat, dry 12 hours and light sanding with 320 grit paper. 2. Application of the final matt varnish YO-05M785 catalyzed with 10% catalyst YC — M402. Dry for 24 hours.

Acrylic transparent deep matt varnish

1. JL---M070/----- 2. JO-03M077/----- 1. Wood veneer base sanded with 180 grit paper. Spray two coats of JL — M070 with an interval of 8 hours and sand with 320 grit sandpaper. After the second layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Apply JO-03M077. Dry for 24 hours.

PU colored high-gloss

1. PL---M005/--C01 2. FB---M066/CS045 1. MDF board base. Apply two coats of PL-M005 / -C01 by spraying. Spacing between layers of 8 hours and sand with 320 grit paper. After the last layer, dry for 8 hours and sand with 320 grit paper. 2. Apply the final gloss varnish FB — M066 / CS045. Dry for 48 hours. Polish if needed.

PU colored matt varnish

1. FL---M042/--C01 2. FO25M060/CS105 1. MDF board base. Apply two coats of FL — M042 / -C01 by spraying. Spacing between layers of 12 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Apply matt varnish FO-25M060 / CS105. Dry for 24 hours.

PU black varnish with high acrylic gloss

1. PL---M005/--C01 2. FO-25M060/R9005 3. JB---M671/----- 1. MDF board base. Apply two coats of PL-M005 / -C01 by spraying. Interval between layers of 8 hours and sand with 320 grit paper. After the last layer, dry for 8 hours and sand with 320 grit paper. 2. Apply matt varnish FO-25M060 / RAL9005. Dry for 16 hours and lightly sand with 400 grit paper. 3. Apply acrylic gloss varnish JB — M671. Dry for 48 hours. Polish if needed.

PU black matt varnish

1. FL---M042/--C01 2. FO25M060/R9005 1. MDF board base. Apply two coats of FL — M042 / -C01 by spraying. Interval between layers of 12 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 320 grit paper. 2. Apply matt varnish FO-25M060 / RAL9005. Dry for 24 hours.

Open pore with acrylic black deep matte varnish

1. JO-15M800/R9005 2. JO-03M077/----- 1. Ash veneer base sanded with 180 grit paper. Spray two to three coats of JO-15M800 / RAL9005 . Interval between layers of 4-6 hours and sand with 320 grit paper. After the last layer, dry for 12 hours and lightly sand with 400 grit paper. 2. Apply acrylic matt varnish JO-03M077. Dry for 24 hours.